Kontroler lotu FC F4 1S BETAFPV OSD NO RX
Note: If you are using EU-LBT firmware radio controller, you might find that you can't bind successfully to F4 Brushless FC. Here are the solutions we provide for you. Thanks to Sebastian Abramowski for giving us the important feedback about binding to EU-LBT firmware radio controller.
Comparison F3 Brushless FC F4 Brushless FC
SPECIFICATIONS OF FC
CPU: STM32F411CEU6 (100MHZ )
Six-Axis: MPU-6000 triaxial accelerometer / triaxial gyroscope (SPI connection)
Size: 26mm x 26mm, fully compatible with the Inductrix quad frame, Beta65 Pro frame, Beta75 Pro frame, BWhoop B06 frame and mounting pattern
Firmware version: Betaflight MATEKF411RX 3.4.0 for F4 Brushless FC (SPI Frsky RX)
Firmware version: Betaflight MATEKF411 for F4 Brushless FC (No RX)
OSD: Built-in BetaFlight OSD (STM32 controls OSD chip over SPI in DMA mode)
Built in SPI Frsky D8 protocol native receiver, compatible with almost ALL Frsky radios(e.g. Taranis X9D/X9D Plus/X7) or Frsky compatible transmitter module
Power Cable: 55mm, with JST-PH 2.0 connector, AKA PowerWhoop connector
Weight: 4g
DIAGRAM FOR F4 1S BRUSHLESS FC (Frsky RX+OSD)
Status LED
There are 3 LEDs on the bottom of the board to indicate the status, including Receiver LED ( Green), FC Status LED ( Red ) and FC Power LED ( Blue ).
SPI Frsky Receiver
Currently the built in Frsky receiver is compatible with Taranis, Taranis Plus, X9E, Horus X12S, XJT Modules. Pay attention, this is a SPI connection receiver. In Betaflight Configuration, it should be setted as FRSKY_D receiver (aka Frsky D8 mode) or FRSKY_X receiver (aka Frsky D16 mode) in SPI RX mode.
The Frsky D16 unstable connection issue is totally resolved since Betaflight 3.4.1. Nowadays, the default configuration from factory is Frsky D16 mode (FRSKY_X).
Binding Procedure FOR F4 1S BRUSHLESS FC (FRSKY RX+OSD)
The binding procedure is reversed as usual. No need to click the bind button when power on.
Power on the board, either by connecting the battery or USB power. Then the green receiver LED start to flash.
The second step, click the bind button for 3s. Then the green receiver LED will be solid on. This means that the receiver is in bind mode and you could start to bind your radio transmitter.
For detail procedure of binding, please check the SPI Frsky Receiver Binding Manual.
Some pilots would complaint that it is definitely not a long range FC. It looses signal with my transmitter far too often and for what appears to be no reason. This issue is often caused by the location of the antenna. You should keep the antenna away from the FC board to get a stronger signal. For example, run the singal upwards. Thanks for Harley Finberg's advice.
CLI DUMP of F4 1S Brushless FC (Frsky RX+OSD)
You can get the Cli dump of F4 1S Brushless FC here on the BETAFPV Support Freshdesk.
SPECIFICATIONS OF ESC
Power supply: 1S
Current: 5A continuous and peak 6A (3 seconds)
Support BLHeliSuite programmable
Factory firmware: O_L_5_REV16_6.HEX
Signal Support: D-shot150, D-shot300, D-shot600, Oneshot125, Multishot, PWM
DIAGRAM FOR F4 1S BRUSHLESS FC (NO RX+OSD)
HOW TO CONNECT THE RECEIVER
For the details about how to connect the receiver and configure in Betaflight, please check the F4 1S Brushless FC (No RX) Manual
RECOMMENDED PARTS LIST
Frame: Beta65 Pro frame / Beta75 Pro frame
Props: 31mm 4-Blades props (for Beta65 Pro frame) / 40mm 4-blades props (for Beta75 Pro frame)
Motors: 0703 motors / 0603 motors
Battery: 550mAh 1S batteries
PACKAGE
1 * F4 1S brushless flight controller
4 * M1.2x4mm screws
4 * M1.4x5mm screws
4 * Anti-vibration ruber dampers
- Sklep: Sklep z dronami i akcesoriami RC NOB Can Fly
- Kategoria: CZĘŚCI DO DRONÓW I MODELI RC/Kontrolery lotu
- Marka: BetaFPV
- Dostępność: na pytanie
- Zaktualizowany: 1.6.2024
- Cena: 155.00 zł
